Inner cab corner panels from DC

67nukeford · Post by **67nukeford** » Thu Apr 19, 2012 8:33 am

Well, I've shot an email with this thread link, and one from another site off to them, to show that there is defintively a market for these. We'll see what they have to say.

GHOST · Post by **GHOST** » Thu Apr 19, 2012 1:34 pm

Just wondering is it these cab corners your talking about
http://www.andysautosport.com/ford/1967 ... key_parts/

sargentrs · Post by **sargentrs** » Thu Apr 19, 2012 8:51 pm

Not exactly. We're referring to the back side of these. http://www.fordification.com/forum/view ... 7&p=422038

67nukeford · Post by **67nukeford** » Fri Apr 20, 2012 10:18 am

Here are a few pics. This is looking at the inside panels on the rear cab corners, with the cab laying on it's back.

sargentrs · Post by **sargentrs** » Fri Apr 20, 2012 3:59 pm

That's similar to my issue. Apparently, the PO ran over something because my right rear cab corner is bent back toward the bed resulting in a crack on the outside, which has rusted, and dinged up on the inside. I can repair or replace the outside but I'm not sure how much I can do with the inside. Driver's side's in good shape but the passenger side is pretty caved in and started rusting from the inside out due to the water running in from the outside. Sure could use a replacement panel. Hello....DC?!

69f-100 · Post by **69f-100** » Fri Apr 20, 2012 5:14 pm

67nukeford wrote:I want to get enough replies here and on another site, to send them the links, and show them that these would be worth making.

i could use a set as well.

come on dc

67nukeford · Post by **67nukeford** » Fri Apr 27, 2012 7:50 am

Still no word from DC yet....

convincor · Post by **convincor** » Mon Sep 24, 2012 6:17 pm

They'd sell thousands of them if they made them.
Even if it were made universal for left or right as long and that rib was stamped would be the key.
I've done flat panels in the past but never liked the look... its the just not right.
I could use two right now!!!

cole71 · Post by **cole71** » Mon Sep 24, 2012 7:22 pm

I needed two as well when my cab was being painted. Luckily, I had a guy locally make a set for me, they were spot on and fit nicely.

convincor · Post by **convincor** » Thu Sep 27, 2012 6:44 am

I just ordered outer cab corners from DC the other day and added in the notes "if you had the inners I'd be buying them also".
Got a call yesterday to tell me they where out of one side and would have them for 2 months...

And said as for the inners try SCHOTT PANELS or EMS... While I haven't called the don't show anything on there websites.

Red Mercury · Post by **Red Mercury** » Tue Oct 09, 2012 12:15 am

I would buy the inner panels too. I can't figure out why someone doesn't have them, they are always rotted out in my area. For every 2 outer panels that DC sells, they would sell 2 inner ones as well!

convincor · Post by **convincor** » Tue Oct 09, 2012 8:17 am

I would think EVERYBODY who bought outers would also buy inners.
When does the outer rot and not the inner?? For them to say they don't get much call for them is BS.

The FORDification.com Forums

Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC

Re: Inner cab corner panels from DC